Wednesday, 13 February 2013

Carburetor Break Down Part 4 (Day 179)

 I was doing so well.  I got the first butterfly out of carb no. 1 easy peasy.  And it will be as easy to get carb 4 apart.  But I had no idea until this morning that carbs 2 and 3 are a completely different kettle of fish.  There is no cap to remove and no easy circlip.  This is carb no. 3.   
 There is no easy circlip removal on this one.  One end (below) is manufactured to be non-removable.
But the other end has a nut on it which is held in place by a tabbed washer that is bent up to prevent the nut coming lose.  I anticipate getting this one off quite easily.
 
 Now carb no. 2 is the problem. 
 As per carb no.3, one end is manufactured to be non-removable
And the other end (below) is another matter.  
 No nut to remove.  There is however this (click to enlarge).  It looks like there is some kind of pin in there that goes all the way through to the other side.  If this is a removable split pin, I need to find a punch of the exact size to push it out.  It is hollow.
Someone tell me the trick for this one please.








Tuesday, 12 February 2013

Carburetor Break Down Part 3 (Day 176)

I was getting a lot of jip (english for: aggravation) on the forum (GS Resources) about not stripping the butterflies out.  One of the reasons I did not do it was because I could find no mention of it anywhere.  It is not shown or described on any of the carb strip/rebuild tutorials.  So I did it anyway.  It is important to get the very best fit cross head screwdriver to get the butterfly screws out.  It would get messy if they were stripped.  Here we go:
 First you have to get the rusty old end cap off.  Then remove the circlip.
 
 And the plastic washer.
 
 Then you remove the 2 screws holding the butterfly valve onto the spindle and remove the spindle.
 
 Noting how the bottom part of the spring catches around the lug.
 This leaves you with a rubber seal at both ends.  These will need replacing as they are not very soft.  I have read about carbs leaking air in this area.  So MORE carb bits to buy.
 Here they are
 
 I also discovered another set of O rings (just how many are there in a set of carbs?) under the choke nut.
 There is also a rubber seal on the top part of the choke nut.  OK lets replace them as well!

Saturday, 9 February 2013

Carburetor Break Down Part 2 (Day 175)

 Now getting down to the nitty gritty.  First get the float pins out without breaking anything.
 


 Then try and get the needle valve retaining bracket off to remove the needle valve.  I got them all out except for one which needed to be Dremelled (new verb).
Then remove the needle valve as a complete unit using a pair of pliers.  Gently of course.
 
Looking at the needle valves it looked like there was some wear on the tips but I could not feel it with my finger nail.  I think it was just marking.  In any case the whole valve is being replaced as they come in the carb refurb kits I now have.
 

 Then I removed the choke valves.  This again was not a straight forward job.  The height of choke valve nut and the recess of the ring spanner meant that there was only a mm of grip.  One of the valve nuts got a little burred.  It was also very difficult to hold the carb body and apply enough force to turn the nut.  More concoction did the trick.
 

 
 
I got all the idle jets out OK except I still have not retrieved the little rubber O ring.  It must be right down the bottom of the hole.

Now to get the carb bodies and all the bits ultrasonically cleaned.  Then vapour blast the bodies and see what options I can find for anodizing.
 I am still wondering about these bits.  I have to remove this plate around one of the throttle butterful valves (more concoction) and then what happens to these springs?  Most of what I have read tells me not to try and dismantle the butterfly valves.  But this spring is really rotten and I would like to get it off to replace it. 
 That would mean undoing this nut.

Pilot Jet Shananigans (Day 175)

Those pesky pilot jets have caused me no end of problems.  I machined (with my Dremel) a screwdriver to the exact .0359 thou size (thank you Ed Ness - see his CV Carburetor Rebuild Tutorial).  It looked like 2 of them were already damaged like the main jets.  And they would not come out.  I used my concoction (50% thinners and 50% brake fluid) and after a lot of effort I got one out.  The other one was impossible and now had a completely flat top.  This one was difficult (click on image to enlarge):
 This is what it looked like when I got it out.
 But for the really difficult one I had to adopt a new strategy.  Firstly I drilled the top out then I inserted and banged in a Torx driver of approximately the right size.  I attached a socket set lever and bingo, it came out.  The thread is still good in the carb body too:
This is the tool I made to do this little trick:



Monday, 4 February 2013

More Main Jet Shananigans

So I now have all the main jets out.  One of them seems to have a very non OEM couple of washers and a couple are quite damaged by hamfisted "mechanics".
 How could you cause such damage?  This has been damaged when it was screwed in.  The burred part is where pressure would have been applied if you were tightening it up in a clockwise manner.  But why use such force?
 This jet has a ring marking around it. But at least they all read "115".  Let's hope that is the correct size.

Sunday, 3 February 2013

Carburetor Workbench

For some with large homes, purpose built workshops and the like, getting a decent place to work on your carburettors is an easy task.  At my house it is not.  Our garage is the store for my property and holiday letting business and it is full of spare furniture, 3 washing machines, 2 driers and over 50 sets of bed linen and towels.  Not to mention my set of acoustic drums and a 1000 watt sub amplifier.  But I finally did it.  Lots of junk thrown out and all the rest re-organised. Now I have a workbench, a small carpet on the floor (so much easier to stand on than concrete), a desk lamp and my tools to hand.  Let's get to work.







Carburetor Break Down part 1 (Day 169)

I have dug out a place in the garage to start some work on the carbs and engine.  I started with the carbs today.  I read all the relevant documents and webpages including:
 
 
 
and these resources are hugely valuable and should be digested fully before you start.  Let me add my own cautionary notes:
 
1.  It's very important to get the correct size screwdriver bits to remove any of these carburettor screws and jets.  I had to cut slots in 3 of my external screws with my Dremel as the impact driver bit was not working.  Had I hit the driver any harder I may have damaged the carbs themselves.  Some of the jets screws and the choke rail screws were already chewed up quite badly.  Since we have owned this bike since new and never opened the carbs I can only assume that they are fitted like this.
 
2.  I would recommend loosening all the float bowl, carb caps and gang plate screws before you break the carbs down into separate units.  It is far easier to get a rusted/seized carb bowl screw out when you are holding the gang of four carbs than holding a single carb and trying it.  Also with the gang all intact it is easier to hold the carbs and use an impact driver to loosen those bolts.
 
3.  Have a jam jar of concoction ready and nearby.  I discovered that this solution of 50% brake fluid and 50% cellulose thinners is the best solution for getting seized exhaust bolts out.  It also works really well on carb jets, carb bolts and stuck choke actuation rails.
 
Here is the first part of my breakdown.  I have recorded some photos to remind me about some of the parts so I will know how to reassemble.  For instance some of the gang plate screws have washers (where they are holding other metal parts) and some don't.
 
 The bowls have washers
 The tops don't.
 This one was seized to the metal part it was holding.
 Some with washers and some without.
 These choke activation rail screws were quite chewed up before I started.

 The tube joining the carbs together have very small O rings that will need replacing.
Choke activation rod was very tight and was difficult to move.  Some concoction sorted that out.
 This was my worst float bowl.  Pretty grimy but I have seen worse.
 Apply some concoction to the mail jet.

I found this main jet like this and wonder if they were factory assembled like it.  As far as I know the carbs have never been apart.  So why are they burred like this?
There is a washer under the main jet.
 Pushing the needle jet out (using a wood dowel - not seen).
 Top view of needle jet.
The needle jet.
Airscrew - spring is still down the tube.